![]() ![]() The soundbar is only 3.5 pounds heavy, so you don’t have to worry about cracking the wall behind it. Keep in mind that the unit is 31 inches wide, 3.75 inches tall and 2 inches deep, so it will look much better on your wall if you own a 42 inch or larger TV screen. All of the equipment needed is included in the package, so you don’t have to worry about finding the right tools. Like with any other soundbar around, this system can be installed underneath your flat screen TV with the help of a wall mounting bracket. Both of the units have a simple, but very appealing design. The subwoofer comes with a glossy finish, while the soundbar itself is only glossy on the outer edges. The soundbar looks very slick and slim, the finishing touches are quite attractive and the front grille will draw just the right amount of attention. If you only need to change the programming for some of the bar buttons, follow the three steps in the sequence previously described to redo any previous programming.This piece of audio equipment is one of the better-looking Polk systems you can find. NOTE: This procedure removes ALL of your bar’s remote control programming. The SurroundBar 3000 will continue to respond to the provided credit card remote control. You’ll know that previously learned codes have been successfully erased when the power LED blinks orange and red in succession. Repeat steps 1-3 to program “Volume Down” ( ), Mute and Power buttons ( ).Ĭode Erasing Procedure: If you have programmed your SurroundBar 3000 to respond to a remote control and you no longer want it to do so, then you can erase the codes by pressing the LEARN key for about two seconds while the unit is in standby mode (power LED is red). After the 4th button press the status indicator LED should blink green for about 3 seconds. With each tap the status LED should blink quickly (like a strobe). Quickly tap the “Volume Up” ( ) button approximately 4 times. While holding your TV’s remote within 1-2 feet of the bar, Press and hold “LEARN” on the bar untilĢ. However, we strongly recommend that you program the SurroundBar 3000 IHT to also respond to your existing remote control using the steps illustrated below thereby enabling you to operate everything using a single remote.Įxample: To have your bar learn the “Volume Up” command of your remote control:ġ. Programming Instructions: Your SurroundBar 3000 IHT is currently programmed to respond to the remote control that is included with the product. Your remote will control the SurroundBar 3000 IHT without programming. Important Note: If adjusting your TV’s volume also adjusts the volume of your bar, then following the instructions below is not necessary. HOW TO SET UP A REMOTE CONTROL FOR YOUR SURROUNDBAR 3000 IHT Adjust the volume until what you hear sounds natural to you in your normal viewing location. ![]() To set the subwoofer’s volume, play a variety of source material- some music, a movie sound track with great special effects, a movie chapter or a part of a concert in which people are speaking. This will ensure the system produces the best sound. The next thing you’ll want to do is adjust the subwoofer to blend with your bar. Then use the TV remote control to adjust the volume as you normally do. Set the volume to a normal listening level (do not use the remote control).Īfter you make these adjustments, your SurroundBar 3000 IHT should always be louder than your TV speakers. Then, using the volume control buttons on your bar, Turn your TV volume all the way down using the controlģ. (See “HOW TO SETUP A REMOTE CONTROL FOR YOUR SURROUNDBAR 3000 IHT” on this page.)Ģ. Up and down control commands of your TV remote. If necessary, program your bar to respond to the volume Use the following steps to adjust the volume balance between your TV and the bar:ġ. Your SurroundBar 3000 IHT will make your TV sound much better.To enjoy the best performance from your bar, you’ll want it to play louder than your TV. If you can’t turn off your TV internal speakers, don’t worry. The setting to turn off your TV’s internal speakers should be here. Next, look for an option to control audio functions On your TV remote control, find a “menu” or “setup” button.Ģ. It’s impossible to give specific instructions on how to turn off the speakers for every TV, but here’s a way to do it that covers many of the TVs out there.ġ. If your bar is connected to your TV, there’s a very good chance your TV speakers are also playing. ![]() If you don’t, turn up the volume on the bar using its volume control buttons. HOW TO OPTIMIZE THE SOUND WHEN TV SPEAKERS ARE ON ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |